更新硬件SDK

sdk/合宙/air780e/csdk/luatos-soc-2022/project/cloud_speaker/inc/RTE_Device.h

@@ -0,0 +1,350 @@
+#ifndef __RTE_DEVICE_H
+#define __RTE_DEVICE_H
+
+#include "ec618.h"
+
+/*  Peripheral IO Mode Select, Must Configure First !!!
+    Note, when receiver works in DMA_MODE, interrupt is also enabled to transfer tailing bytes.
+*/
+
+#define POLLING_MODE            0x1
+#define DMA_MODE                0x2
+#define IRQ_MODE                0x3
+#define UNILOG_MODE             0x4
+
+#define RTE_UART0_TX_IO_MODE    UNILOG_MODE
+#define RTE_UART0_RX_IO_MODE    IRQ_MODE
+#define USART0_RX_TRIG_LVL      (30)
+
+#define RTE_UART1_TX_IO_MODE    DMA_MODE
+#define RTE_UART1_RX_IO_MODE    DMA_MODE
+
+#define RTE_UART2_TX_IO_MODE    POLLING_MODE
+#define RTE_UART2_RX_IO_MODE    DMA_MODE
+
+#define RTE_SPI0_IO_MODE        POLLING_MODE
+
+#define RTE_SPI1_IO_MODE        POLLING_MODE
+
+#define RTE_I2C0_IO_MODE        POLLING_MODE
+#define RTE_I2C1_IO_MODE        POLLING_MODE
+
+
+// I2C0 (Inter-integrated Circuit Interface) [Driver_I2C0]
+// Configuration settings for Driver_I2C0 in component ::Drivers:I2C
+#define RTE_I2C0                        1
+
+// { PAD_PIN28},  // 0 : gpio13 / 2 : I2C0 SCL
+// { PAD_PIN27},  // 0 : gpio12 / 2 : I2C0 SDA
+#define RTE_I2C0_SCL_BIT                28			// AUDIO use 28
+#define RTE_I2C0_SCL_FUNC               PAD_MUX_ALT2
+
+#define RTE_I2C0_SDA_BIT                27			// AUDIO use 27
+#define RTE_I2C0_SDA_FUNC               PAD_MUX_ALT2
+
+// DMA
+//   Tx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_I2C0_DMA_TX_EN              0
+#define RTE_I2C0_DMA_TX_REQID           DMA_REQUEST_I2C0_TX
+//   Rx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_I2C0_DMA_RX_EN              0
+#define RTE_I2C0_DMA_RX_REQID           DMA_REQUEST_I2C0_RX
+
+// I2C1 (Inter-integrated Circuit Interface) [Driver_I2C1]
+// Configuration settings for Driver_I2C1 in component ::Drivers:I2C
+#define RTE_I2C1                        1
+
+// { PAD_PIN20},  // 0 : gpio5  / 2 : I2C1 SCL
+// { PAD_PIN19},  // 0 : gpio4  / 2 : I2C1 SDA
+#define RTE_I2C1_SCL_BIT                20
+#define RTE_I2C1_SCL_FUNC               PAD_MUX_ALT2
+
+#define RTE_I2C1_SDA_BIT                19
+#define RTE_I2C1_SDA_FUNC               PAD_MUX_ALT2
+
+// DMA
+//   Tx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_I2C1_DMA_TX_EN              1
+#define RTE_I2C1_DMA_TX_REQID           DMA_REQUEST_I2C1_TX
+//   Rx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_I2C1_DMA_RX_EN              1
+#define RTE_I2C1_DMA_RX_REQID           DMA_REQUEST_I2C1_RX
+
+
+// UART0 (Universal asynchronous receiver transmitter) [Driver_USART0]
+// Configuration settings for Driver_USART0 in component ::Drivers:USART
+#define RTE_UART0_CTS_PIN_EN            0
+#define RTE_UART0_RTS_PIN_EN            0
+
+// { PAD_PIN27},  // 0 : gpio12 / 3 : UART0 RTSn
+// { PAD_PIN28},  // 0 : gpio13 / 3 : UART0 CTSn
+// { PAD_PIN29},  // 0 : gpio14 / 3 : UART0 RXD
+// { PAD_PIN30},  // 0 : gpio15 / 3 : UART0 TXD
+#define RTE_UART0_RTS_BIT               27
+#define RTE_UART0_RTS_FUNC              PAD_MUX_ALT3
+
+#define RTE_UART0_CTS_BIT               28
+#define RTE_UART0_CTS_FUNC              PAD_MUX_ALT3
+
+#define RTE_UART0_RX_BIT                29
+#define RTE_UART0_RX_FUNC               PAD_MUX_ALT3
+
+#define RTE_UART0_TX_BIT                30
+#define RTE_UART0_TX_FUNC               PAD_MUX_ALT3
+
+// DMA
+//  Tx
+//    Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_UART0_DMA_TX_REQID          DMA_REQUEST_USART0_TX
+//  Rx
+//    Channel    <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_UART0_DMA_RX_REQID          DMA_REQUEST_USART0_RX
+
+// UART1 (Universal asynchronous receiver transmitter) [Driver_USART1]
+// Configuration settings for Driver_USART1 in component ::Drivers:USART
+#define RTE_UART1_CTS_PIN_EN            1
+#define RTE_UART1_RTS_PIN_EN            1
+
+// { PAD_PIN31},  // 0 : gpio16  / 1 : UART1 RTS
+// { PAD_PIN32},  // 0 : gpio17  / 1 : UART1 CTS
+// { PAD_PIN33},  // 0 : gpio18  / 1 : UART1 RXD
+// { PAD_PIN34},  // 0 : gpio19  / 1 : UART1 TXD
+#define RTE_UART1_RTS_BIT               31
+#define RTE_UART1_RTS_FUNC              PAD_MUX_ALT1
+
+#define RTE_UART1_CTS_BIT               32
+#define RTE_UART1_CTS_FUNC              PAD_MUX_ALT1
+
+#define RTE_UART1_RX_BIT                33
+#define RTE_UART1_RX_FUNC               PAD_MUX_ALT1
+
+#define RTE_UART1_TX_BIT                34
+#define RTE_UART1_TX_FUNC               PAD_MUX_ALT1
+
+// DMA
+//   Tx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_UART1_DMA_TX_REQID          DMA_REQUEST_USART1_TX
+//   Rx
+//     Channel    <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_UART1_DMA_RX_REQID          DMA_REQUEST_USART1_RX
+
+// UART2 (Universal asynchronous receiver transmitter) [Driver_USART2]
+// Configuration settings for Driver_USART2 in component ::Drivers:USART
+#define RTE_UART2_CTS_PIN_EN            0
+#define RTE_UART2_RTS_PIN_EN            0
+
+// { PAD_PIN25},  // 0 : gpio10 / 3 : UART2 RXD
+// { PAD_PIN26},  // 0 : gpio11 / 3 : UART2 TXD
+#define RTE_UART2_RX_BIT                25
+#define RTE_UART2_RX_FUNC               PAD_MUX_ALT3
+
+#define RTE_UART2_TX_BIT                26
+#define RTE_UART2_TX_FUNC               PAD_MUX_ALT3
+
+
+// DMA
+//   Tx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_UART2_DMA_TX_REQID          DMA_REQUEST_USART2_TX
+//   Rx
+//     Channel    <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_UART2_DMA_RX_REQID          DMA_REQUEST_USART2_RX
+
+// SPI0 (Serial Peripheral Interface) [Driver_SPI0]
+// Configuration settings for Driver_SPI0 in component ::Drivers:SPI
+#define RTE_SPI0                        1
+
+// { PAD_PIN21},  // 0 : gpio16 / 1 : UART1 RTS / 2 : SPI0 SSn
+// { PAD_PIN22},  // 0 : gpio11 / 1 : UART1 CTS / 2 : SPI0 MOSI
+// { PAD_PIN23},  // 0 : gpio14 / 1 : UART1 RXD / 2 : SPI0 MISO
+// { PAD_PIN24},  // 0 : gpio15 / 1 : UART1 TXD / 2 : SPI0 SCLK
+#define RTE_SPI0_SSN_BIT                21
+#define RTE_SPI0_SSN_FUNC               PAD_MUX_ALT2
+
+#define RTE_SPI0_MOSI_BIT               22
+#define RTE_SPI0_MOSI_FUNC              PAD_MUX_ALT2
+
+#define RTE_SPI0_MISO_BIT               23
+#define RTE_SPI0_MISO_FUNC              PAD_MUX_ALT2
+
+#define RTE_SPI0_SCLK_BIT               24
+#define RTE_SPI0_SCLK_FUNC              PAD_MUX_ALT2
+
+#define RTE_SPI0_SSN_GPIO_INSTANCE      1
+#define RTE_SPI0_SSN_GPIO_INDEX         0
+
+// DMA
+//   Tx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_SPI0_DMA_TX_REQID           DMA_REQUEST_SPI0_TX
+
+//   Rx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_SPI0_DMA_RX_REQID           DMA_REQUEST_SPI0_RX
+
+// SPI1 (Serial Peripheral Interface) [Driver_SPI1]
+// Configuration settings for Driver_SPI1 in component ::Drivers:SPI
+#define RTE_SPI1                        1
+
+// { PAD_PIN13},  // 0 : gpio2 / 1 : UART0 RTSn / 3 : SPI1 SSn
+// { PAD_PIN14},  // 0 : gpio3 / 1 : UART0 CTSn / 3 : SPI1 MOSI
+// { PAD_PIN15},  // 0 : gpio4 / 1 : UART0 RXD  / 3 : SPI1 MISO
+// { PAD_PIN16},  // 0 : gpio5 / 1 : UART0 TXD  / 3 : SPI1 SCLK
+#define RTE_SPI1_SSN_BIT                13
+#define RTE_SPI1_SSN_FUNC               PAD_MUX_ALT3
+
+#define RTE_SPI1_MOSI_BIT               14
+#define RTE_SPI1_MOSI_FUNC              PAD_MUX_ALT3
+
+#define RTE_SPI1_MISO_BIT               15
+#define RTE_SPI1_MISO_FUNC              PAD_MUX_ALT3
+
+#define RTE_SPI1_SCLK_BIT               16
+#define RTE_SPI1_SCLK_FUNC              PAD_MUX_ALT3
+
+#define RTE_SPI1_SSN_GPIO_INSTANCE      0
+#define RTE_SPI1_SSN_GPIO_INDEX         2
+
+// DMA
+//   Tx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_SPI1_DMA_TX_REQID           DMA_REQUEST_SPI1_TX
+
+//   Rx
+//     Channel     <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
+#define RTE_SPI1_DMA_RX_REQID           DMA_REQUEST_SPI1_RX
+
+
+// PWM0 Controller [Driver_PWM0]
+// Configuration settings for Driver_PWM0 in component ::Drivers:PWM
+#define RTE_PWM                         1
+
+#define EFUSE_INIT_MODE POLLING_MODE
+#define L2CTLS_INIT_MODE POLLING_MODE
+
+#define FLASH_BARE_RW_MODE 1
+
+
+
+
+
+#define RTE_UART0                       1
+#define RTE_UART1                       1
+#define RTE_UART2                       1
+/* to enable external thermal */
+#define EXTERNAL_NTC_EXIST              0
+
+
+#if (RTE_UART1 == 1)
+#define UART1_DTR_PAD_INDEX             26     // GPIO11
+#define UART1_DTR_GPIO_INSTANCE         0
+#define UART1_DTR_GPIO_PIN              11
+
+#define UART1_RI_PAD_INDEX              44     // AONIO 4 = GPIO24
+#define UART1_RI_GPIO_INSTANCE          1
+#define UART1_RI_GPIO_PIN               8
+#define UART1_RI_PWM_INSTANCE           1
+#define UART1_RI_PWM_CLK_ID             FCLK_TIMER1
+#define UART1_RI_PWM_CLK_SEL            FCLK_TIMER1_SEL_26M
+
+#define UART1_DCD_PAD_INDEX             45     // AONIO 5 = GPIO25
+#define UART1_DCD_GPIO_INSTANCE         1
+#define UART1_DCD_GPIO_PIN              9
+#endif
+
+#if (RTE_UART2 == 1)
+#define UART2_DTR_PAD_INDEX             25     // GPIO10
+#define UART2_DTR_GPIO_INSTANCE         0
+#define UART2_DTR_GPIO_PIN              10
+
+#define UART2_RI_PAD_INDEX              43     // AONIO 3 = GPIO23
+#define UART2_RI_GPIO_INSTANCE          1
+#define UART2_RI_GPIO_PIN               7
+#define UART2_RI_PWM_INSTANCE           0
+#define UART2_RI_PWM_CLK_ID             FCLK_TIMER0
+#define UART2_RI_PWM_CLK_SEL            FCLK_TIMER0_SEL_26M
+
+#define UART2_DCD_PAD_INDEX             47     // AONIO 7 = GPIO27
+#define UART2_DCD_GPIO_INSTANCE         1
+#define UART2_DCD_GPIO_PIN              11
+#endif
+
+
+#define NETLIGHT_PAD_INDEX              46     // AONIO 6 = GPIO26
+#define NETLIGHT_PAD_ALT_FUNC           PAD_MUX_ALT5
+#define NETLIGHT_PWM_INSTANCE           3
+
+//USIM1 OPTION1
+#define USIM1_URST_OP1_PAD_INDEX             19     // GPIO4
+#define USIM1_URST_OP1_GPIO_INSTANCE         0
+#define USIM1_URST_OP1_GPIO_PIN              4
+#define USIM1_UCLK_OP1_PAD_INDEX             20     // GPIO5
+#define USIM1_UCLK_OP1_GPIO_INSTANCE         0
+#define USIM1_UCLK_OP1_GPIO_PIN              5
+#define USIM1_UIO_OP1_PAD_INDEX              21     // GPIO6
+#define USIM1_UIO_OP1_GPIO_INSTANCE          0
+#define USIM1_UIO_OP1_GPIO_PIN               6
+
+//USIM1 OPTION2
+#define USIM1_UIO_OP2_PAD_INDEX              27     // GPIO12
+#define USIM1_UIO_OP2_GPIO_INSTANCE          0
+#define USIM1_UIO_OP2_GPIO_PIN               12
+#define USIM1_URST_OP2_PAD_INDEX             28     // GPIO13
+#define USIM1_URST_OP2_GPIO_INSTANCE         0
+#define USIM1_URST_OP2_GPIO_PIN              13
+#define USIM1_UCLK_OP2_PAD_INDEX             29     // GPIO14
+#define USIM1_UCLK_OP2_GPIO_INSTANCE         0
+#define USIM1_UCLK_OP2_GPIO_PIN              14
+
+//USIM1 clock latched by AONIO, for example, use AONIO-6 test on EVB
+#define AONIO_6_PAD_INDEX        46     // AONIO 6 = GPIO26
+#define AONIO_6_GPIO_INSTANCE    1
+#define AONIO_6_GPIO_PIN         10
+
+#define RTE_CSPI0                       0
+
+#define RTE_CSPI0_MCLK_PAD_ADDR         39
+#define RTE_CSPI0_MCLK_FUNC             PAD_MUX_ALT1
+
+#define RTE_CSPI0_PCLK_PAD_ADDR         35
+#define RTE_CSPI0_PCLK_FUNC             PAD_MUX_ALT1
+
+#define RTE_CSPI0_CS_PAD_ADDR           36
+#define RTE_CSPI0_CS_FUNC               PAD_MUX_ALT1
+
+#define RTE_CSPI0_SDO0_PAD_ADDR         37
+#define RTE_CSPI0_SDO0_FUNC             PAD_MUX_ALT1
+
+#define RTE_CSPI0_SDO1_PAD_ADDR         38
+#define RTE_CSPI0_SDO1_FUNC             PAD_MUX_ALT1
+
+// DMA CSPI0 Request ID
+#define RTE_CSPI0_DMA_RX_REQID          DMA_REQUEST_I2S0_RX
+
+// CSPI1 Configuration
+#define RTE_CSPI1                       1
+
+#define RTE_CSPI1_MCLK_PAD_ADDR         18
+#define RTE_CSPI1_MCLK_FUNC             PAD_MUX_ALT1
+
+#define RTE_CSPI1_PCLK_PAD_ADDR         19
+#define RTE_CSPI1_PCLK_FUNC             PAD_MUX_ALT1
+
+#define RTE_CSPI1_CS_PAD_ADDR           20
+#define RTE_CSPI1_CS_FUNC               PAD_MUX_ALT1
+
+#define RTE_CSPI1_SDO0_PAD_ADDR         21
+#define RTE_CSPI1_SDO0_FUNC             PAD_MUX_ALT1
+
+#define RTE_CSPI1_SDO1_PAD_ADDR         22
+#define RTE_CSPI1_SDO1_FUNC             PAD_MUX_ALT1
+
+// DMA CSPI1 Request ID
+#define RTE_CSPI1_DMA_RX_REQID          DMA_REQUEST_I2S1_RX
+
+#endif  /* __RTE_DEVICE_H */

sdk/合宙/air780e/csdk/luatos-soc-2022/project/cloud_speaker/inc/audio_extern.h

@@ -0,0 +1,39 @@
+#ifndef __AUDIO_EXTERN_H__
+#define __AUDIO_EXTERN_H__
+extern const unsigned char audio0[];
+extern const unsigned char audio1[];
+extern const unsigned char audio10[];
+extern const unsigned char audio100[];
+extern const unsigned char audio1000[];
+extern const unsigned char audio10000[];
+extern const unsigned char audio2[];
+extern const unsigned char audio3[];
+extern const unsigned char audio4[];
+extern const unsigned char audio5[];
+extern const unsigned char audio6[];
+extern const unsigned char audio7[];
+extern const unsigned char audio8[];
+extern const unsigned char audio9[];
+extern const unsigned char audiodot[];
+extern const unsigned char audioshoukuanchenggong[];
+extern const unsigned char audioyuan[];
+extern const unsigned char audiozhifubao[];
+extern const int audio0Size;
+extern const int audio1Size;
+extern const int audio10Size;
+extern const int audio100Size;
+extern const int audio1000Size;
+extern const int audio10000Size;
+extern const int audio2Size;
+extern const int audio3Size;
+extern const int audio4Size;
+extern const int audio5Size;
+extern const int audio6Size;
+extern const int audio7Size;
+extern const int audio8Size;
+extern const int audio9Size;
+extern const int audiodotSize;
+extern const int audioshoukuanchenggongSize;
+extern const int audioyuanSize;
+extern const int audiozhifubaoSize;
+#endif

sdk/合宙/air780e/csdk/luatos-soc-2022/project/cloud_speaker/inc/audio_task.h

@@ -0,0 +1,41 @@
+#ifndef __AUDIO_TASK__
+#define __AUDIO_TASK__
+#include "queue.h"
+// #include "audio_play.h"
+#include "luat_audio_play_ec618.h"
+typedef struct
+{
+    uint32_t priority;
+    uint32_t playType;
+    union
+    {
+        struct
+        {
+            char *data;
+            uint8_t len;
+        } tts;
+        struct
+        {
+            luat_audio_play_info_t *info;
+            uint8_t count;
+        } file;
+    } message;
+    void * userParam;
+} audioQueueData;
+
+typedef enum
+{
+    MONEY_PLAY = 0,
+    PAD_PLAY,
+    SYS_PLAY
+} AUDIO_PLAY_PRIORITY;
+
+typedef enum
+{
+    TTS_PLAY = 0,
+    FILE_PLAY,
+} AUDIO_PLAY_TYPE;
+
+
+void audio_task_init(void);
+#endif

sdk/合宙/air780e/csdk/luatos-soc-2022/project/cloud_speaker/inc/mqtt_publish.h

@@ -0,0 +1,18 @@
+#ifndef __MQTT_PUBLISH_H__
+#define __MQTT_PUBLISH_H__
+#include "MQTTClient.h"
+typedef struct mqtt_publish_para
+{
+    mqttSendMsg* publish;
+    void (*callback)(int result);
+}mqtt_publish_para_t;
+
+
+typedef enum MQTT_PUBLISH_RESULT
+{
+    MQTT_PUBLISH_SUCCESS,
+    MQTT_PUBLISH_FAIL,
+    MQTT_NOT_READY,
+    NETWORK_NOT_READY
+}MQTT_PUBLISH_RESULT_E;
+#endif

sdk/合宙/air780e/csdk/luatos-soc-2022/project/cloud_speaker/inc/mqtt_status.h

@@ -0,0 +1,5 @@
+#ifndef __MQTT_STATUS_H_
+#define __MQTT_STATUS_H_
+bool getNetStatus();
+bool getServerStatus();
+#endif