mirror of
https://gitee.com/beecue/fastbee.git
synced 2025-12-21 02:15:55 +08:00
更新硬件SDK
This commit is contained in:
kerwincui
@@ -0,0 +1,350 @@
|
||||
#ifndef __RTE_DEVICE_H
|
||||
#define __RTE_DEVICE_H
|
||||
|
||||
#include "ec618.h"
|
||||
|
||||
/* Peripheral IO Mode Select, Must Configure First !!!
|
||||
Note, when receiver works in DMA_MODE, interrupt is also enabled to transfer tailing bytes.
|
||||
*/
|
||||
|
||||
#define POLLING_MODE 0x1
|
||||
#define DMA_MODE 0x2
|
||||
#define IRQ_MODE 0x3
|
||||
#define UNILOG_MODE 0x4
|
||||
|
||||
#define RTE_UART0_TX_IO_MODE UNILOG_MODE
|
||||
#define RTE_UART0_RX_IO_MODE IRQ_MODE
|
||||
#define USART0_RX_TRIG_LVL (30)
|
||||
|
||||
#define RTE_UART1_TX_IO_MODE DMA_MODE
|
||||
#define RTE_UART1_RX_IO_MODE DMA_MODE
|
||||
|
||||
#define RTE_UART2_TX_IO_MODE POLLING_MODE
|
||||
#define RTE_UART2_RX_IO_MODE DMA_MODE
|
||||
|
||||
#define RTE_SPI0_IO_MODE POLLING_MODE
|
||||
|
||||
#define RTE_SPI1_IO_MODE POLLING_MODE
|
||||
|
||||
#define RTE_I2C0_IO_MODE POLLING_MODE
|
||||
#define RTE_I2C1_IO_MODE POLLING_MODE
|
||||
|
||||
|
||||
// I2C0 (Inter-integrated Circuit Interface) [Driver_I2C0]
|
||||
// Configuration settings for Driver_I2C0 in component ::Drivers:I2C
|
||||
#define RTE_I2C0 1
|
||||
|
||||
// { PAD_PIN28}, // 0 : gpio13 / 2 : I2C0 SCL
|
||||
// { PAD_PIN27}, // 0 : gpio12 / 2 : I2C0 SDA
|
||||
#define RTE_I2C0_SCL_BIT 28 // AUDIO use 28
|
||||
#define RTE_I2C0_SCL_FUNC PAD_MUX_ALT2
|
||||
|
||||
#define RTE_I2C0_SDA_BIT 27 // AUDIO use 27
|
||||
#define RTE_I2C0_SDA_FUNC PAD_MUX_ALT2
|
||||
|
||||
// DMA
|
||||
// Tx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_I2C0_DMA_TX_EN 0
|
||||
#define RTE_I2C0_DMA_TX_REQID DMA_REQUEST_I2C0_TX
|
||||
// Rx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_I2C0_DMA_RX_EN 0
|
||||
#define RTE_I2C0_DMA_RX_REQID DMA_REQUEST_I2C0_RX
|
||||
|
||||
// I2C1 (Inter-integrated Circuit Interface) [Driver_I2C1]
|
||||
// Configuration settings for Driver_I2C1 in component ::Drivers:I2C
|
||||
#define RTE_I2C1 1
|
||||
|
||||
// { PAD_PIN20}, // 0 : gpio5 / 2 : I2C1 SCL
|
||||
// { PAD_PIN19}, // 0 : gpio4 / 2 : I2C1 SDA
|
||||
#define RTE_I2C1_SCL_BIT 20
|
||||
#define RTE_I2C1_SCL_FUNC PAD_MUX_ALT2
|
||||
|
||||
#define RTE_I2C1_SDA_BIT 19
|
||||
#define RTE_I2C1_SDA_FUNC PAD_MUX_ALT2
|
||||
|
||||
// DMA
|
||||
// Tx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_I2C1_DMA_TX_EN 1
|
||||
#define RTE_I2C1_DMA_TX_REQID DMA_REQUEST_I2C1_TX
|
||||
// Rx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_I2C1_DMA_RX_EN 1
|
||||
#define RTE_I2C1_DMA_RX_REQID DMA_REQUEST_I2C1_RX
|
||||
|
||||
|
||||
// UART0 (Universal asynchronous receiver transmitter) [Driver_USART0]
|
||||
// Configuration settings for Driver_USART0 in component ::Drivers:USART
|
||||
#define RTE_UART0_CTS_PIN_EN 0
|
||||
#define RTE_UART0_RTS_PIN_EN 0
|
||||
|
||||
// { PAD_PIN27}, // 0 : gpio12 / 3 : UART0 RTSn
|
||||
// { PAD_PIN28}, // 0 : gpio13 / 3 : UART0 CTSn
|
||||
// { PAD_PIN29}, // 0 : gpio14 / 3 : UART0 RXD
|
||||
// { PAD_PIN30}, // 0 : gpio15 / 3 : UART0 TXD
|
||||
#define RTE_UART0_RTS_BIT 27
|
||||
#define RTE_UART0_RTS_FUNC PAD_MUX_ALT3
|
||||
|
||||
#define RTE_UART0_CTS_BIT 28
|
||||
#define RTE_UART0_CTS_FUNC PAD_MUX_ALT3
|
||||
|
||||
#define RTE_UART0_RX_BIT 29
|
||||
#define RTE_UART0_RX_FUNC PAD_MUX_ALT3
|
||||
|
||||
#define RTE_UART0_TX_BIT 30
|
||||
#define RTE_UART0_TX_FUNC PAD_MUX_ALT3
|
||||
|
||||
// DMA
|
||||
// Tx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_UART0_DMA_TX_REQID DMA_REQUEST_USART0_TX
|
||||
// Rx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_UART0_DMA_RX_REQID DMA_REQUEST_USART0_RX
|
||||
|
||||
// UART1 (Universal asynchronous receiver transmitter) [Driver_USART1]
|
||||
// Configuration settings for Driver_USART1 in component ::Drivers:USART
|
||||
#define RTE_UART1_CTS_PIN_EN 1
|
||||
#define RTE_UART1_RTS_PIN_EN 1
|
||||
|
||||
// { PAD_PIN31}, // 0 : gpio16 / 1 : UART1 RTS
|
||||
// { PAD_PIN32}, // 0 : gpio17 / 1 : UART1 CTS
|
||||
// { PAD_PIN33}, // 0 : gpio18 / 1 : UART1 RXD
|
||||
// { PAD_PIN34}, // 0 : gpio19 / 1 : UART1 TXD
|
||||
#define RTE_UART1_RTS_BIT 31
|
||||
#define RTE_UART1_RTS_FUNC PAD_MUX_ALT1
|
||||
|
||||
#define RTE_UART1_CTS_BIT 32
|
||||
#define RTE_UART1_CTS_FUNC PAD_MUX_ALT1
|
||||
|
||||
#define RTE_UART1_RX_BIT 33
|
||||
#define RTE_UART1_RX_FUNC PAD_MUX_ALT1
|
||||
|
||||
#define RTE_UART1_TX_BIT 34
|
||||
#define RTE_UART1_TX_FUNC PAD_MUX_ALT1
|
||||
|
||||
// DMA
|
||||
// Tx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_UART1_DMA_TX_REQID DMA_REQUEST_USART1_TX
|
||||
// Rx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_UART1_DMA_RX_REQID DMA_REQUEST_USART1_RX
|
||||
|
||||
// UART2 (Universal asynchronous receiver transmitter) [Driver_USART2]
|
||||
// Configuration settings for Driver_USART2 in component ::Drivers:USART
|
||||
#define RTE_UART2_CTS_PIN_EN 0
|
||||
#define RTE_UART2_RTS_PIN_EN 0
|
||||
|
||||
// { PAD_PIN25}, // 0 : gpio10 / 3 : UART2 RXD
|
||||
// { PAD_PIN26}, // 0 : gpio11 / 3 : UART2 TXD
|
||||
#define RTE_UART2_RX_BIT 25
|
||||
#define RTE_UART2_RX_FUNC PAD_MUX_ALT3
|
||||
|
||||
#define RTE_UART2_TX_BIT 26
|
||||
#define RTE_UART2_TX_FUNC PAD_MUX_ALT3
|
||||
|
||||
|
||||
// DMA
|
||||
// Tx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_UART2_DMA_TX_REQID DMA_REQUEST_USART2_TX
|
||||
// Rx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_UART2_DMA_RX_REQID DMA_REQUEST_USART2_RX
|
||||
|
||||
// SPI0 (Serial Peripheral Interface) [Driver_SPI0]
|
||||
// Configuration settings for Driver_SPI0 in component ::Drivers:SPI
|
||||
#define RTE_SPI0 1
|
||||
|
||||
// { PAD_PIN21}, // 0 : gpio16 / 1 : UART1 RTS / 2 : SPI0 SSn
|
||||
// { PAD_PIN22}, // 0 : gpio11 / 1 : UART1 CTS / 2 : SPI0 MOSI
|
||||
// { PAD_PIN23}, // 0 : gpio14 / 1 : UART1 RXD / 2 : SPI0 MISO
|
||||
// { PAD_PIN24}, // 0 : gpio15 / 1 : UART1 TXD / 2 : SPI0 SCLK
|
||||
#define RTE_SPI0_SSN_BIT 21
|
||||
#define RTE_SPI0_SSN_FUNC PAD_MUX_ALT2
|
||||
|
||||
#define RTE_SPI0_MOSI_BIT 22
|
||||
#define RTE_SPI0_MOSI_FUNC PAD_MUX_ALT2
|
||||
|
||||
#define RTE_SPI0_MISO_BIT 23
|
||||
#define RTE_SPI0_MISO_FUNC PAD_MUX_ALT2
|
||||
|
||||
#define RTE_SPI0_SCLK_BIT 24
|
||||
#define RTE_SPI0_SCLK_FUNC PAD_MUX_ALT2
|
||||
|
||||
#define RTE_SPI0_SSN_GPIO_INSTANCE 1
|
||||
#define RTE_SPI0_SSN_GPIO_INDEX 0
|
||||
|
||||
// DMA
|
||||
// Tx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_SPI0_DMA_TX_REQID DMA_REQUEST_SPI0_TX
|
||||
|
||||
// Rx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_SPI0_DMA_RX_REQID DMA_REQUEST_SPI0_RX
|
||||
|
||||
// SPI1 (Serial Peripheral Interface) [Driver_SPI1]
|
||||
// Configuration settings for Driver_SPI1 in component ::Drivers:SPI
|
||||
#define RTE_SPI1 1
|
||||
|
||||
// { PAD_PIN13}, // 0 : gpio2 / 1 : UART0 RTSn / 3 : SPI1 SSn
|
||||
// { PAD_PIN14}, // 0 : gpio3 / 1 : UART0 CTSn / 3 : SPI1 MOSI
|
||||
// { PAD_PIN15}, // 0 : gpio4 / 1 : UART0 RXD / 3 : SPI1 MISO
|
||||
// { PAD_PIN16}, // 0 : gpio5 / 1 : UART0 TXD / 3 : SPI1 SCLK
|
||||
#define RTE_SPI1_SSN_BIT 13
|
||||
#define RTE_SPI1_SSN_FUNC PAD_MUX_ALT3
|
||||
|
||||
#define RTE_SPI1_MOSI_BIT 14
|
||||
#define RTE_SPI1_MOSI_FUNC PAD_MUX_ALT3
|
||||
|
||||
#define RTE_SPI1_MISO_BIT 15
|
||||
#define RTE_SPI1_MISO_FUNC PAD_MUX_ALT3
|
||||
|
||||
#define RTE_SPI1_SCLK_BIT 16
|
||||
#define RTE_SPI1_SCLK_FUNC PAD_MUX_ALT3
|
||||
|
||||
#define RTE_SPI1_SSN_GPIO_INSTANCE 0
|
||||
#define RTE_SPI1_SSN_GPIO_INDEX 2
|
||||
|
||||
// DMA
|
||||
// Tx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_SPI1_DMA_TX_REQID DMA_REQUEST_SPI1_TX
|
||||
|
||||
// Rx
|
||||
// Channel <0=>0 <1=>1 <2=>2 <3=>3 <4=>4 <5=>5 <6=>6 <7=>7
|
||||
#define RTE_SPI1_DMA_RX_REQID DMA_REQUEST_SPI1_RX
|
||||
|
||||
|
||||
// PWM0 Controller [Driver_PWM0]
|
||||
// Configuration settings for Driver_PWM0 in component ::Drivers:PWM
|
||||
#define RTE_PWM 1
|
||||
|
||||
#define EFUSE_INIT_MODE POLLING_MODE
|
||||
#define L2CTLS_INIT_MODE POLLING_MODE
|
||||
|
||||
#define FLASH_BARE_RW_MODE 1
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
#define RTE_UART0 1
|
||||
#define RTE_UART1 1
|
||||
#define RTE_UART2 1
|
||||
/* to enable external thermal */
|
||||
#define EXTERNAL_NTC_EXIST 0
|
||||
|
||||
|
||||
#if (RTE_UART1 == 1)
|
||||
#define UART1_DTR_PAD_INDEX 26 // GPIO11
|
||||
#define UART1_DTR_GPIO_INSTANCE 0
|
||||
#define UART1_DTR_GPIO_PIN 11
|
||||
|
||||
#define UART1_RI_PAD_INDEX 44 // AONIO 4 = GPIO24
|
||||
#define UART1_RI_GPIO_INSTANCE 1
|
||||
#define UART1_RI_GPIO_PIN 8
|
||||
#define UART1_RI_PWM_INSTANCE 1
|
||||
#define UART1_RI_PWM_CLK_ID FCLK_TIMER1
|
||||
#define UART1_RI_PWM_CLK_SEL FCLK_TIMER1_SEL_26M
|
||||
|
||||
#define UART1_DCD_PAD_INDEX 45 // AONIO 5 = GPIO25
|
||||
#define UART1_DCD_GPIO_INSTANCE 1
|
||||
#define UART1_DCD_GPIO_PIN 9
|
||||
#endif
|
||||
|
||||
#if (RTE_UART2 == 1)
|
||||
#define UART2_DTR_PAD_INDEX 25 // GPIO10
|
||||
#define UART2_DTR_GPIO_INSTANCE 0
|
||||
#define UART2_DTR_GPIO_PIN 10
|
||||
|
||||
#define UART2_RI_PAD_INDEX 43 // AONIO 3 = GPIO23
|
||||
#define UART2_RI_GPIO_INSTANCE 1
|
||||
#define UART2_RI_GPIO_PIN 7
|
||||
#define UART2_RI_PWM_INSTANCE 0
|
||||
#define UART2_RI_PWM_CLK_ID FCLK_TIMER0
|
||||
#define UART2_RI_PWM_CLK_SEL FCLK_TIMER0_SEL_26M
|
||||
|
||||
#define UART2_DCD_PAD_INDEX 47 // AONIO 7 = GPIO27
|
||||
#define UART2_DCD_GPIO_INSTANCE 1
|
||||
#define UART2_DCD_GPIO_PIN 11
|
||||
#endif
|
||||
|
||||
|
||||
#define NETLIGHT_PAD_INDEX 46 // AONIO 6 = GPIO26
|
||||
#define NETLIGHT_PAD_ALT_FUNC PAD_MUX_ALT5
|
||||
#define NETLIGHT_PWM_INSTANCE 3
|
||||
|
||||
//USIM1 OPTION1
|
||||
#define USIM1_URST_OP1_PAD_INDEX 19 // GPIO4
|
||||
#define USIM1_URST_OP1_GPIO_INSTANCE 0
|
||||
#define USIM1_URST_OP1_GPIO_PIN 4
|
||||
#define USIM1_UCLK_OP1_PAD_INDEX 20 // GPIO5
|
||||
#define USIM1_UCLK_OP1_GPIO_INSTANCE 0
|
||||
#define USIM1_UCLK_OP1_GPIO_PIN 5
|
||||
#define USIM1_UIO_OP1_PAD_INDEX 21 // GPIO6
|
||||
#define USIM1_UIO_OP1_GPIO_INSTANCE 0
|
||||
#define USIM1_UIO_OP1_GPIO_PIN 6
|
||||
|
||||
//USIM1 OPTION2
|
||||
#define USIM1_UIO_OP2_PAD_INDEX 27 // GPIO12
|
||||
#define USIM1_UIO_OP2_GPIO_INSTANCE 0
|
||||
#define USIM1_UIO_OP2_GPIO_PIN 12
|
||||
#define USIM1_URST_OP2_PAD_INDEX 28 // GPIO13
|
||||
#define USIM1_URST_OP2_GPIO_INSTANCE 0
|
||||
#define USIM1_URST_OP2_GPIO_PIN 13
|
||||
#define USIM1_UCLK_OP2_PAD_INDEX 29 // GPIO14
|
||||
#define USIM1_UCLK_OP2_GPIO_INSTANCE 0
|
||||
#define USIM1_UCLK_OP2_GPIO_PIN 14
|
||||
|
||||
//USIM1 clock latched by AONIO, for example, use AONIO-6 test on EVB
|
||||
#define AONIO_6_PAD_INDEX 46 // AONIO 6 = GPIO26
|
||||
#define AONIO_6_GPIO_INSTANCE 1
|
||||
#define AONIO_6_GPIO_PIN 10
|
||||
|
||||
#define RTE_CSPI0 0
|
||||
|
||||
#define RTE_CSPI0_MCLK_PAD_ADDR 39
|
||||
#define RTE_CSPI0_MCLK_FUNC PAD_MUX_ALT1
|
||||
|
||||
#define RTE_CSPI0_PCLK_PAD_ADDR 35
|
||||
#define RTE_CSPI0_PCLK_FUNC PAD_MUX_ALT1
|
||||
|
||||
#define RTE_CSPI0_CS_PAD_ADDR 36
|
||||
#define RTE_CSPI0_CS_FUNC PAD_MUX_ALT1
|
||||
|
||||
#define RTE_CSPI0_SDO0_PAD_ADDR 37
|
||||
#define RTE_CSPI0_SDO0_FUNC PAD_MUX_ALT1
|
||||
|
||||
#define RTE_CSPI0_SDO1_PAD_ADDR 38
|
||||
#define RTE_CSPI0_SDO1_FUNC PAD_MUX_ALT1
|
||||
|
||||
// DMA CSPI0 Request ID
|
||||
#define RTE_CSPI0_DMA_RX_REQID DMA_REQUEST_I2S0_RX
|
||||
|
||||
// CSPI1 Configuration
|
||||
#define RTE_CSPI1 1
|
||||
|
||||
#define RTE_CSPI1_MCLK_PAD_ADDR 18
|
||||
#define RTE_CSPI1_MCLK_FUNC PAD_MUX_ALT1
|
||||
|
||||
#define RTE_CSPI1_PCLK_PAD_ADDR 19
|
||||
#define RTE_CSPI1_PCLK_FUNC PAD_MUX_ALT1
|
||||
|
||||
#define RTE_CSPI1_CS_PAD_ADDR 20
|
||||
#define RTE_CSPI1_CS_FUNC PAD_MUX_ALT1
|
||||
|
||||
#define RTE_CSPI1_SDO0_PAD_ADDR 21
|
||||
#define RTE_CSPI1_SDO0_FUNC PAD_MUX_ALT1
|
||||
|
||||
#define RTE_CSPI1_SDO1_PAD_ADDR 22
|
||||
#define RTE_CSPI1_SDO1_FUNC PAD_MUX_ALT1
|
||||
|
||||
// DMA CSPI1 Request ID
|
||||
#define RTE_CSPI1_DMA_RX_REQID DMA_REQUEST_I2S1_RX
|
||||
|
||||
#endif /* __RTE_DEVICE_H */
|
||||
@@ -0,0 +1,80 @@
|
||||
/*
|
||||
* Copyright (c) 2022 OpenLuat & AirM2M
|
||||
*
|
||||
* Permission is hereby granted, free of charge, to any person obtaining a copy of
|
||||
* this software and associated documentation files (the "Software"), to deal in
|
||||
* the Software without restriction, including without limitation the rights to
|
||||
* use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
|
||||
* the Software, and to permit persons to whom the Software is furnished to do so,
|
||||
* subject to the following conditions:
|
||||
*
|
||||
* The above copyright notice and this permission notice shall be included in all
|
||||
* copies or substantial portions of the Software.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
|
||||
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
|
||||
* FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
|
||||
* COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
|
||||
* IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
|
||||
* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
|
||||
*/
|
||||
|
||||
|
||||
#include "common_api.h"
|
||||
#include "FreeRTOS.h"
|
||||
#include "task.h"
|
||||
#include "timer.h"
|
||||
#include "bsp.h"
|
||||
|
||||
|
||||
#define TIMER_INSTANCE (1)
|
||||
|
||||
/** \brief TIMER clock id for clock configuration */
|
||||
#define TIMER_CLOCK_ID (FCLK_TIMER1)
|
||||
|
||||
/** \brief TIMER clock source select */
|
||||
#define TIMER_CLOCK_SOURCE (FCLK_TIMER1_SEL_26M)
|
||||
|
||||
/** \brief TIMER instance IRQ number */
|
||||
#define TIMER_INSTANCE_IRQ (PXIC0_TIMER1_IRQn)
|
||||
|
||||
|
||||
/// @brief 定时器中断服务函数
|
||||
void Timer_ISR()
|
||||
{
|
||||
if (TIMER_getInterruptFlags(TIMER_INSTANCE) & TIMER_MATCH0_INTERRUPT_FLAG)
|
||||
{
|
||||
DBG("timer demo interrupt is running");
|
||||
TIMER_clearInterruptFlags(TIMER_INSTANCE, TIMER_MATCH0_INTERRUPT_FLAG);
|
||||
}
|
||||
}
|
||||
static void Timer_Init(void *param)
|
||||
{
|
||||
TIMER_driverInit();//定时器内部初始化
|
||||
CLOCK_setClockSrc(TIMER_CLOCK_ID, TIMER_CLOCK_SOURCE);//选择定时器时钟来源
|
||||
CLOCK_setClockDiv(TIMER_CLOCK_ID, 1);//设置时钟分频
|
||||
TimerConfig_t timer1_config;
|
||||
TIMER_getDefaultConfig(&timer1_config);
|
||||
timer1_config.reloadOption=TIMER_RELOAD_ON_MATCH0;//重装通道选项 可以选择MATCH0，MATCH1，MATCH2
|
||||
timer1_config.match0=0xc65d40;//重装值 500ms ,定时器频率为26MHZ，13000000=0xc65d40
|
||||
TIMER_init(TIMER_INSTANCE, &timer1_config);
|
||||
TIMER_interruptConfig(TIMER_INSTANCE, TIMER_MATCH0_SELECT, TIMER_INTERRUPT_LEVEL);//中断配置
|
||||
TIMER_interruptConfig(TIMER_INSTANCE, TIMER_MATCH1_SELECT, TIMER_INTERRUPT_DISABLED);
|
||||
TIMER_interruptConfig(TIMER_INSTANCE, TIMER_MATCH2_SELECT, TIMER_INTERRUPT_DISABLED);
|
||||
XIC_SetVector(TIMER_INSTANCE_IRQ, Timer_ISR);
|
||||
XIC_EnableIRQ(TIMER_INSTANCE_IRQ);
|
||||
TIMER_start(TIMER_INSTANCE);
|
||||
while (1)
|
||||
{
|
||||
DBG("timer demo is running");
|
||||
vTaskDelay(500);
|
||||
}
|
||||
|
||||
}
|
||||
|
||||
void Timer_task_init(void)
|
||||
{
|
||||
xTaskCreate(Timer_Init,"timer_demo",1*1024,NULL,3,NULL);
|
||||
}
|
||||
|
||||
INIT_TASK_EXPORT(Timer_task_init,"1");
|
||||
@@ -0,0 +1,20 @@
|
||||
local TARGET_NAME = "example_timer"
|
||||
local LIB_DIR = "$(buildir)/".. TARGET_NAME .. "/"
|
||||
local LIB_NAME = "lib" .. TARGET_NAME .. ".a "
|
||||
|
||||
target(TARGET_NAME)
|
||||
set_kind("static")
|
||||
set_targetdir(LIB_DIR)
|
||||
--加入代码和头文件
|
||||
add_includedirs("/inc",{public = true})
|
||||
add_files("/src/*.c",{public = true})
|
||||
|
||||
--路径可以随便写,可以加任意路径的代码,下面代码等效上方代码
|
||||
-- add_includedirs(SDK_TOP .. "project/" .. TARGET_NAME .. "/inc",{public = true})
|
||||
-- add_files(SDK_TOP .. "project/" .. TARGET_NAME .. "/src/*.c",{public = true})
|
||||
|
||||
--可以继续增加add_includedirs和add_files
|
||||
--自动链接
|
||||
LIB_USER = LIB_USER .. SDK_TOP .. LIB_DIR .. LIB_NAME .. " "
|
||||
--甚至可以加入自己的库
|
||||
target_end()
|
||||
Reference in New Issue
Block a user