添加智能灯固件代码

firmware/esp-idf/wumei-smart-firmware/examples/peripherals/adc/main/CMakeLists.txt

@@ -0,0 +1,2 @@
+idf_component_register(SRCS "adc1_example_main.c"
+                    INCLUDE_DIRS ".")

firmware/esp-idf/wumei-smart-firmware/examples/peripherals/adc/main/adc1_example_main.c

@@ -0,0 +1,108 @@
+/* ADC1 Example
+
+   This example code is in the Public Domain (or CC0 licensed, at your option.)
+
+   Unless required by applicable law or agreed to in writing, this
+   software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
+   CONDITIONS OF ANY KIND, either express or implied.
+*/
+#include <stdio.h>
+#include <stdlib.h>
+#include "freertos/FreeRTOS.h"
+#include "freertos/task.h"
+#include "driver/gpio.h"
+#include "driver/adc.h"
+#include "esp_adc_cal.h"
+
+#define DEFAULT_VREF    1100        //Use adc2_vref_to_gpio() to obtain a better estimate
+#define NO_OF_SAMPLES   64          //Multisampling
+
+static esp_adc_cal_characteristics_t *adc_chars;
+#if CONFIG_IDF_TARGET_ESP32
+static const adc_channel_t channel = ADC_CHANNEL_6;     //GPIO34 if ADC1, GPIO14 if ADC2
+static const adc_bits_width_t width = ADC_WIDTH_BIT_12;
+#elif CONFIG_IDF_TARGET_ESP32S2
+static const adc_channel_t channel = ADC_CHANNEL_6;     // GPIO7 if ADC1, GPIO17 if ADC2
+static const adc_bits_width_t width = ADC_WIDTH_BIT_13;
+#endif
+static const adc_atten_t atten = ADC_ATTEN_DB_0;
+static const adc_unit_t unit = ADC_UNIT_1;
+
+
+static void check_efuse(void)
+{
+#if CONFIG_IDF_TARGET_ESP32
+    //Check if TP is burned into eFuse
+    if (esp_adc_cal_check_efuse(ESP_ADC_CAL_VAL_EFUSE_TP) == ESP_OK) {
+        printf("eFuse Two Point: Supported\n");
+    } else {
+        printf("eFuse Two Point: NOT supported\n");
+    }
+    //Check Vref is burned into eFuse
+    if (esp_adc_cal_check_efuse(ESP_ADC_CAL_VAL_EFUSE_VREF) == ESP_OK) {
+        printf("eFuse Vref: Supported\n");
+    } else {
+        printf("eFuse Vref: NOT supported\n");
+    }
+#elif CONFIG_IDF_TARGET_ESP32S2
+    if (esp_adc_cal_check_efuse(ESP_ADC_CAL_VAL_EFUSE_TP) == ESP_OK) {
+        printf("eFuse Two Point: Supported\n");
+    } else {
+        printf("Cannot retrieve eFuse Two Point calibration values. Default calibration values will be used.\n");
+    }
+#else
+#error "This example is configured for ESP32/ESP32S2."
+#endif
+}
+
+
+static void print_char_val_type(esp_adc_cal_value_t val_type)
+{
+    if (val_type == ESP_ADC_CAL_VAL_EFUSE_TP) {
+        printf("Characterized using Two Point Value\n");
+    } else if (val_type == ESP_ADC_CAL_VAL_EFUSE_VREF) {
+        printf("Characterized using eFuse Vref\n");
+    } else {
+        printf("Characterized using Default Vref\n");
+    }
+}
+
+
+void app_main(void)
+{
+    //Check if Two Point or Vref are burned into eFuse
+    check_efuse();
+
+    //Configure ADC
+    if (unit == ADC_UNIT_1) {
+        adc1_config_width(width);
+        adc1_config_channel_atten(channel, atten);
+    } else {
+        adc2_config_channel_atten((adc2_channel_t)channel, atten);
+    }
+
+    //Characterize ADC
+    adc_chars = calloc(1, sizeof(esp_adc_cal_characteristics_t));
+    esp_adc_cal_value_t val_type = esp_adc_cal_characterize(unit, atten, width, DEFAULT_VREF, adc_chars);
+    print_char_val_type(val_type);
+
+    //Continuously sample ADC1
+    while (1) {
+        uint32_t adc_reading = 0;
+        //Multisampling
+        for (int i = 0; i < NO_OF_SAMPLES; i++) {
+            if (unit == ADC_UNIT_1) {
+                adc_reading += adc1_get_raw((adc1_channel_t)channel);
+            } else {
+                int raw;
+                adc2_get_raw((adc2_channel_t)channel, width, &raw);
+                adc_reading += raw;
+            }
+        }
+        adc_reading /= NO_OF_SAMPLES;
+        //Convert adc_reading to voltage in mV
+        uint32_t voltage = esp_adc_cal_raw_to_voltage(adc_reading, adc_chars);
+        printf("Raw: %d\tVoltage: %dmV\n", adc_reading, voltage);
+        vTaskDelay(pdMS_TO_TICKS(1000));
+    }
+}

firmware/esp-idf/wumei-smart-firmware/examples/peripherals/adc/main/component.mk

@@ -0,0 +1,3 @@
+#
+# Main Makefile. This is basically the same as a component makefile.
+#