#include "bsp_port.h"

// 禁用JTAG引脚,保留SWD引脚
void Sys_DisableJTAGEnableSWD(void)
{
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO,ENABLE); 	//开启AFIO时钟
	GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE); //禁止JTAG功能
}

// PM 初始化
void BSP_PowerInit(void)
{
   	GPIO_InitTypeDef GPIO_InitStructure;
    EXTI_InitTypeDef EXTI_InitStructure;
    NVIC_InitTypeDef NVIC_InitStructure;	
    
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB|RCC_APB2Periph_GPIOC,ENABLE);	
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);
    
    GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_1|GPIO_Pin_12|GPIO_Pin_13;
	GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_Out_PP;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_Init(GPIOB,&GPIO_InitStructure);

    Power_PMD4(0); Power_3V3(0); Power_LCD(0);
    
    // 唤醒/正在充电指示/充电完成
    GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_13|GPIO_Pin_14;
	GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_IPU;
	GPIO_Init(GPIOC,&GPIO_InitStructure);    
    
    /* Configure one bit for preemption priority */
    NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);
  
    /* 配置P[A|B|C|D|E]0为中断源 */
    NVIC_InitStructure.NVIC_IRQChannel = EXTI15_10_IRQn;
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority        = 0;
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure);

    GPIO_InitStructure.GPIO_Pin   = GPIO_Pin_15;
	GPIO_InitStructure.GPIO_Mode  = GPIO_Mode_IPD;
	GPIO_Init(GPIOC,&GPIO_InitStructure);   
    
    GPIO_EXTILineConfig(GPIO_PortSourceGPIOC, GPIO_PinSource15); 
    EXTI_InitStructure.EXTI_Line    = EXTI15_10_IRQn;
    EXTI_InitStructure.EXTI_Mode    = EXTI_Mode_Interrupt;
    EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising; //下降沿中断
    EXTI_InitStructure.EXTI_LineCmd = ENABLE;
    EXTI_Init(&EXTI_InitStructure); 
}

void EXTI15_10_IRQHandler(void)
{
    if(EXTI_GetITStatus(EXTI_Line15) != RESET)
    {
        EXTI_ClearITPendingBit(EXTI_Line15);
        
        if(DevParam.RunPhase == 0)
        {
            BSP_Restart();
        }
    }  
}

// mcu 重新启动
void BSP_Restart(void){
    __set_FAULTMASK(1);
	NVIC_SystemReset();
}